Powered Amplifier QSC RMX 2450 Start Price USD 625.00 Current Price USD 625.00 Time Left - Bid Count 0 Buy It Now Price - Reserve Price - Start Time Tuesday, August 19, 2008 End Time Tuesday, August 26, 2008 Location Holland, PA See more about 'Powered Amplifier QSC RMX 2450' Description QSC Audio Proffessional Powered Amplifier RMX 2450 This amp is in great condition.  i only used it for practicing so it stayed in one spot...no gigging or touring. the only thing missing from it is one of the little rubber stoppers on the bottom that keeps it flat.  looks brand new and works great.  comes with necessary cords.  check out my other items listed for a full pa package if interested.  thank you for looking and good luck! zzounds.com description: The new RMX Series amplifiers give you clean, dynamic power with the legendary QSC sound quality and reliability that pros depend on. The RMX Series delivers unmatched performance at a new breakthrough price.Muscular Power PlantThe power supply is the heart of an amplifier, converting raw AC power from the wall to clean DC for the audio circuitry. The RMX uses a powerful high-current toroidal transformer and ample filter capacitance to ensure generous energy reserves. This makes a critical difference in sound quality, allowing the amp to effortlessly punch out high-level transients, even when driving abusive 2-ohm speaker loads. Superior PerformanceRMX amplifiers deliver true studio-quality sound. A full, complementary output circuit using the highest-grade linear output devices delivers ultra-low distortion (<0.05% THD) and a ruler-flat frequency response. SMT (Surface Mount Technology) triples small-signal component density, enabling us to pack up to 2400 watts of power in a chassis only 2 rack spaces and less than 16 in. deep. And unlike other designs, RMX output devices are direct-mounted to the heat sink for optimum thermal coupling and cooling. FeaturesThe RMX Series is packed full of professional features that increase performance and flexibility:Independent defeatable clip limiters reduce distortion without sacrificing peak performance. Selectable low-frequency filters boost system response, protect speakers and ensure low-end tightness by more precisely matching the amplifier's range to the loudspeakers. Barrier strip, XLR, and 1/4 in. balanced inputs plus Speakon and binding post outputs provide easy connections. Low-noise variable speed fans with rear-to-front air flow keep amplifiers and racks cool. Proven ReliabilityWith over 30 years of building amplifiers for the largest touring companies and venues around the world, you can count on QSC's reputation for designing the most reliable amps available. Technical Info SpecificationsContinuous Power Rating8 Ohms: 500 W4 Ohms: 750 W2 Ohms: 1200 W8 Ohms Bridged Mono: 1500 W4 Ohms Bridged Mono: 2400 WCurrent Consumption: 10 AmpsDistortion (Typical):20 Hz-20 kHz: 10 dB below rated power Less than 0.03% THD 4 and 8 ohms1.0 kHz and below: full rated power Less than 0.03% THD 4 and 8 ohmsFrequency Response: 20 Hz-20 kHz, +/- 1 dB, -3 dB points: 5 Hz-50 kHzDamping Factor, 1 kHz and below: Greater than 300 at 8 ohmsInput Impedance: 10 k ohms unbalanced, 20 k ohms balancedInput Clipping: 10 Vrms (+22 dB)Cooling: Continuously variable-speed fan, rear-to-front air flowConnectors, each channelInput: Active balanced; barrier strip, XLR and 1/4 in. (6.3mm) TRS tip and XLR pin 2 positiveOutput: touch-proof binding posts and Neutrik SpeakonControlsFront: AC switch, Ch. 1 and Ch. 2 gain knobsRear: 10-position DIP switchIndicatorsPower On: Green LEDSignal: Yellow LED, 1 per channelClip: Red LED, 1 per channelAmplifier Protection:Full short circuit, open circuit, thermal, ultrasonic, and RF protectionStable into reactive or mismatched loadsLoad Protection: On/off muting, AC coupling (850, 1450), triac crowbar (2450, on each channel) Place a Bid!