CROWN CTS8200AUSPCN POWER AMPLIFIER B-STOCK WARRANTY Start Price USD 2,389.99 Current Price USD 2,389.99 Time Left - Bid Count 0 Buy It Now Price - Reserve Price - Start Time Thursday, November 06, 2008 End Time Saturday, December 06, 2008 Location Long Island, NY See more about 'CROWN CTS8200AUSPCN POWER AMPLIFIER B-STOCK WARRANTY' Description Crown CTS8200AUSPCN B-StockThese are Factory sealed B-Stock units with full Warranties  I've sold a lot of B-Stock equipment and have owned quite a bit myself.  It is a good way to save money on very expensive systems without having to deal with someone else's used equipment, because all of these units carry a full factory warranty.... These are factory tested units and are working 100%The Crown CTs 8200AUSP/CN power amplifiers have an integrated 3rd generation, DSP-based PIP (Programmable Input Processor) input module. It connects the amplifier to a 100 Mbps Ethernet network allowing it to be remotely controlled and monitored via System Architect software. In addition, the input module allows the transport of real-time digital audio via CobraNet over the same Ethernet network.The CTs 8200AUSP/CN amplifiers connect to a HiQnet audio control/monitor network using standard 100 Mbps Ethernet hardware (switches, Network Interface Cards, and cables). CobraNet audio is available over the same 100 Mbps Ethernet network, providing a simple-to-install, single-plug solution for audio distribution, control, and monitoring.The input module's SHARC DSP processors give the user an enormous amount of digital signal processing. Audio routing, faders, meters, polarity & mute, input compressors, filters, delays, multimode output limiters, error reporting, and load monitoring are all available. A built in noise generator and sine-wave generator provide noise masking and test capabilities. The enhanced AUX port capability allows the user to interface with the amplifier to provide external manual control and monitoring.Input Module Features100 Mbps Ethernet single-plug solution for CobraNet audio, and HiQnet control and monitoring Analog audio inputs allow CobraNet network audio input, CobraNet audio backup, or a hard-wire emergency override of CobraNet audio 24 bit digital to analog conversion with 32 bit, floating point DSP processing Up to 18 assignable filters per channel with 9 different filter types including all-pass filters Over 2 seconds of delay available per channel Input compressors and output limiters for each channel Dual, uncorrelated noise generators for noise masking Sine generator Load supervision Full error reporting Firmware upgrades via the network 10 user selectable presets Reliable FLASH memory backup of all parameters Three Year, No-Fault, Fully Transferable Warranty completely protects yourinvestment and guarantees its specificationsPowerDual, 8 Channels Driven:4 ohm (per ch): 200W (1kHz); 175W(20Hz-20kHz)8 ohm (per ch): 160W (1kHz); 155W (20Hz-20kHz)70V (per ch): 200W (1kHz); 185W (20Hz-20kHz) Dual, 1 Channel Driven:4 ohm (per ch): 270W (1kHz); 230W(20Hz-20kHz)8 ohm (per ch): 220W (1kHz); 220W (20Hz-20kHz)70V (per ch): 250W (1kHz); 230W (20Hz-20kHz) Bridge-Mono, 4 Channel-Pairs Driven:8 ohm (per ch): 400W (1kHz); 350W(20Hz-20kHz)16 ohm (per ch): 320W (1kHz); 310W (20Hz-20kHz)100V (per ch): 200W (1kHz); 185W (20Hz-20kHz) Bridge-Mono, 1 Channel-Pair Driven:8 ohm (per ch): 540W (1kHz); 460W(20Hz-20kHz)16 ohm (per ch): 440W (1kHz); 440W (20Hz-20kHz)100V (perch): 250W (1kHz); 230W (20Hz-20kHz)Input Module SpecificationsAux Connector: Configurable for AUX input, AUX output and Listen Bus. Listen Bus is also supported through CobraNet Network Connector: The dual RJ45 CobraNet connectors allow a Primary & Secondary connection to the 100Mb Ethernet network. Should the Primary connection lose link activity with the network, the input module will automatically switch to the Secondary connection to ensure uninterrupted audio and control. The indicators on the RJ45 connectors display network information concerning the Ethernet and CobraNet connections Preset Indicator: Signals the number of the current preset, if active, by flashing a series of flashes equal to the current preset number IQ Data Indicator: Flashes when the module receives a valid command that is addressed to the CTs 4200AUSP/CN Reset/Preset Switch: Used to change presets, restore settings to factory default or restore all the presets to the factory defaults. During operation of the switch, the Data indicator flashes as an aid to the user. Accessible with a straightened paper clip through the rear panel, the switch selects the next user preset if pressed for less than 2 seconds, resets the module to preset "0" if pressed for more than 2 seconds Memory Backup: NOn-volatile FLASH memories for backup of run-time parameters, presets, and program storage Communications: 100Mb fast Ethernet conforming to IEEE 802.3 DSP Processing: Two processors, 32 bit, Floating Point, 724 µs latency D/A and A/D Conversion: 24 bit Latency:DSP processing: 1 ma or 1000 µsDigital-to-analogconversion: 250 µsAnalog-to-digital conversion: 250 µsAmplifier: 100µsTotal: 1.6 ms or 1000 µs Dynamic Range: 103 dB typical (A-weighted, 20Hz-20kHz, audio sourced from muted CobraNet channel) Distortion: <0.1% THD+N, 20Hz-20kHz Frequency Response: +/-0.5dB, 20Hz-20kHz Input/Output Monitor Accuracy: Typically +/-1dB Maximum Input Level: +20dBuAmplifier SpecificationsFrequency Respones (at 1W, 20Hz-20kHz): +/-0.5dB Phase Response (at 1W, 10Hz-20kHz): +/-35° Signal To Noise Ratio below rated power (20Hz-20kHz): 100dB unweighted Total Harmonic Distortion (THD) at 1W from 20Hz-20kHz: <0.05% Intermodulation Distortion (IMD) 60Hz and 7kHz at 4:1, from 163 milliwatts to full bandwidth power: <0.05% (typical) Damping Factor: 10Hz to 400Hz: >180 Crosstalk (below rated power, 20Hz to 1kHz): >80dB Common Mode Rejection (CMR) (20Hz to 1kHz): >50dB DC Output Offset (shorted input): <+/-5mV Input Impedance (nominal): 20 kilohms balanced, 10 kilohms unbalanced Maximum Input Level (before input compression): +20dBu Load Impedance (Note: safe with all types of loads):Stereo: 4/8 and 25 ohms (70V)Bridge Mono: 8/16 and 50 ohms (100V) Voltage Gain (at maximum level setting), 1.4V sensitivity:4/8 ohm operation: 20:1 (26dB)70V operation: 50:1 (34dB)100V operation: 71.4:1 (37dB) Required AC Mains: 120V 60Hz, 220/230/240V/50 Hz Power Draw at Idle (120VAC mains, all channels in 4/8 ohm mode): 58W Power Draw at Idle (120VAC mains, all channels in 70V mode): 77W Cooling: Continuously variable speed forced air, front-to-back airflow Dimensions (W x H x D): 19" x 5.25" x 16.25" Front Panel Indicators:Bridge modeReadySignalClipThermalFaultDataPower Front Panel Controls:Power Switch Back Panel Connectors:Output Connectors: One four-pole terminal strip for every two channels with touch-proof cover. Accepts up to 10 AWG terminal forksInput Connectors: Removable Phoenix-style barrier connectors for balanced input. Also can be used as a CobraNet input or a backup for CobraNet Protection SystemsThermal Level ControlFualt Isolation TopologyFaultHighpass FilterAC under/over voltage protectionPower fuseInrush limitingVariable speed fan I accept US Postal Money Orders and PayPal! Shipping is only $18.00 in the lower 48 states Thanks for checking it out! Place a Bid!